Getting Started with Plumbing Basics When Installing a Bathtub
Getting Started with Plumbing Basics When Installing a Bathtub
Blog Article
This article down below on the subject of A Step-by-Step Guide to Installing a Bathtub is without a doubt captivating. Have a go and draw your own conclusions.
Mounting a bathtub isn't specifically brain surgery, yet it does require strong plumbing, woodworking, and sometimes, tiling abilities. Changing an old bathtub with a new one is likewise a moderately challenging project. If the old tub is readily obtainable, the project can relocate rapidly; if you have to open up a wall surface to get rid of the old tub as well as position the new tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need a helper to move out the old bathtub and embeded in the brand-new one. Make sure you have certified on your own for the work and fit trying it. As opposed to working with a service provider to take control of a halfway-completed project, it is much better to think about using one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This write-up will help you mount a brand-new tub in your shower room if you have already bought a new bathtub as well as do not need to alter the plan of your previous supply of water pipes.
Your devices as well as product checklist must make up the following:
Planning for the Installment
First of all, the supporting framework provided with the bathroom should be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to stop strain on the bathtub.
Fit the adaptable tap connectors to the bottom of both faucets using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom should currently prepare to be suited its last placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you need to do is detach the water supply. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing faucets can be fairly problematic because of the limited access that is frequently the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipelines have actually been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning throughout this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing compound.
Prior to carrying on to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bath tub
Making use of the two wood boards under its feet, put the bathtub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also adjusting the feet on the bath tub till the level reads degree.
To set up taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Switch on the supply of water and inspect all joints and new pipework for leakages and tighten them if essential. Fill up the bath tub as well as additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the manufacturer's user's manual. Tiling as well as securing around the bath tub needs to wait up until the bath tub has actually been used at least once as this will settle it into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin making sure that the washing machines are in area in between the faucet and the sink. Safeguard the faucet in place with the supplier provided backnut. Once the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to fracture a rigid seal, creating the water to permeate the wall surface in between the bathroom as well as the tiling, causing problems with moisture and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are sold in tubes and cartridges, and are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the bathtub with water prior to securing, to enable the movement experienced when the bathtub remains in usage. The sealant can split rather early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you liked our excerpt on Installing A Bathtub. Thanks for taking time to read through our article. Loved our entry? Please share it. Help someone else find it. Thank you for taking the time to read it.
View Report this page